• Technical Data

    A Designer Solution For Modern Buildings

    Alubond U.S.A is the brand name for the new technology Aluminum Composite Building Panel from American Building Technologies, Illinois, U.S.A. The panel is a composite consisting of two layers of aluminum skin sandwiching a fire rated core in a continuous co-extrusion process. This new generation technology of mechanical and chemical bonding gives Alubond Panels an exceptional bond integrity. The outer aluminum skin for exterior grade Alubond U.S.A Panels is coated with PVDF Kynar 500 fluorocarbon coatings. The lower aluminum skin is chromate treated and polyester coated. Technical Data
  • Finishes
    Alubond U.S.A continues its aggressive expansion program with a high speed ultra modern coating line. The new facility will be located in Hamriya Free Zone, Sharjah, UAE and capable of coating PVDF, FEVE, (similar to Lumiflon) Polyester, Dual Color and 5 coat stone series. This High Speed line will be capable of coating upto 1575 mm width. PVDF 2 Coat Grab a suitcase and escape from the reality - http://bestcasinoratings.net.
    PVDF 3 Coat

    Dual Color Coating

    Alubond's Coil coating line has developed a Dual Color Coating technology. Architects and clients now have a choice of having more than one color in the same panel to offer coated coils for composite panels, garage doors and roofing industry amongst other applications. The line's capability includes a wide range of coatings like PVDF, FEVE, Nano Self Cleaning, Ultra Durable Polyester, 5 Coat PVDF natural marble and wood series, Anti scratch and Dual Color Coating Systems. Dual Color Coating Dual Color Coating

    5 Coat Natural Series

    A fully warranted 5 Coat PVDF & Fluropolymer coated Aluminum Composite Panels is now available in natural stone and wood series. Alubond U.S.A range of PVDF & Fluropoleymer (FEVE) paint systems allows a gloss levels from low matt to high gloss upto 90% can be produced. 5 Coat Natural Series

    Stainless Steel Series

    Alubond U.S.A introduces the new technology composite panels in genuine Stainless Steel finishes of brushed (Butler) and high mirror finishes. The natural beauty, flatness and rigidity of stainless steel is now combined with the lightweight, flexible and ease of fabrication of composites making Alubond's Stainless Steel Composites an architects' dream. Stainless Steel Series
  • Maintenance

    Cleaning Methods

    Routine cleaning of the Alubond U.S.A ACP panel surface is recommended. It may be washed with water and mild detergent followed by a clean water rinse. The frequency of cleaning and the choice of suitable cleaning agent depend largely on the position of the building being cleaned and degree of contamination. Do not clean sun-heated surfaces (above 400 C) to avoid rapid drying which may lead to stain formation. The cleaning operation must be followed by a thorough rinse with clean water to ensure the removal of all remnants of the cleansing agent. A final wipe down by means of a sponge, leather or wiper is necessary to avoid water stains. The Alubond U.S.A ACP panel is resistant to industrial atmospheres and is self-cleansing in most environments. As with all claddings, improvements in durability is achieved by an annual wash down with warm water so to avoid the buildup of deposits. The Alubond U.S.A ACP panels is anti static and more self-cleansing than many of the alternatives.


    This manual is applied to the cleaning and maintenance procedures for the external cladding of the Alubond U.S.A ACP panels on which Stove Lacquered - based Fluorocarbon (PVDF), Polyester, and Acrylic paints are coated.


    The purpose of this chapter is to assist project people such as architects, contractors, building owners, et al., who are concerned with and / or engaged in the cleaning and maintenance of the external cladding of the Alubond U.S.A ACP panels, especially in establishing safe and sound cleaning procedures.

    General Notes

    Not only Stove Lacquered - based fluorocarbon coating but also precolor, polyester acrylic resin or normal organic coatings onto aluminum will not show an appreciable amount of dirt collection; however the dirt and soil depends largely on the local atmospheric conditions where the building exists. In heavily industrialized area, coastal areas and the areas where construction works are being carried out, it might be necessary to increase the cleaning frequency, not only for the sake of appearance but also for the purpose of removing the dirt and soil likely to be detrimental to the coating surface. Very often, rainfall is effective to remove dirt and to keep the external cladding clean. In areas of low rainfall, this effect may not be expected and accordingly the cleaning frequency might be increased. Even in the same building, portions which are in direct sight at lower levels might be cleaned more frequently, and less obvious portions might be cleaned less frequently or in some instances hardly at all. And in these areas, detrimental components might be deposited on the coated surface. These factors would determine the cleaning schedule. In planning the actual cleaning schedule of the external cladding, the schedule might be adjusted with other cleaning operations for glass and painted aluminum components.

    Cleaning Frequency

    Cleaning is required more often in the following areas in general:

    Areas Of Low Rainfall

    - Heavily industrialized areas
    - The areas where construction works are being carried out
    - Foggy coastal regions with frequent cycles of condensation and dryness.
    In foggy and coastal regions, frequent cycles of condensation and dryness take place and salty components and dirt tends to deposit. Especially, sheltered areas such as overhangs may be soiled easily because of lack of washing by rain.

    Machine Cleaning

    Once automatic wall cleaning machine is considered to be used, a pre-test should be done in the early stage of equipment design to confirm that there is no detrimental effect on the coating as well as to clarify the cleaning effect and frequency.

    Cleaning Procedures

    After project completion, construction soils including concrete or mortar etc., should be removed as quickly as possible. In most cases, the following suggested frequency would be required to keep the coated surface clean as good as it can remain. Cleaning Procedures

    Soil Removal

    The simplest procedure would be water rinse with moderate pressure to remove the soil. If this does not remove the soil, then a concurrent water spray with sponge should be tested. If the soil is still adhering after drying, then a mild detergent or 5 - 10% IPA (Isopropyl Alcohol) solution will be necessary. In order to remove light soil, it is recommended to do some tests to determine the degree of cleaning actually necessary to accomplish the task. Prior to any cleaner application, a forceful water rinse from top to down is recommended as an initial step of tests. The lower water volume with moderate pressure is much better than the considerable water volume with little pressure. When cleaner is applied, physical rubbing with soft sponges or soft rags fully dipped into the liquid solution is also helpful.

    Clean Detergents / Solutions

    When a mild detergent or 5 - 10% IPA solution is used for removing soil, it should be used with soft sponges and / or soft rags. The washing should be done with uniform pressure, and normally the operation is done with a horizontal motion first and then with a vertical motion. After washing, the surface should be thoroughly rinsed with clean water, and the rinsed surface is air-dried or wiped with chamois, squeegee or lint-free cloth.

    Operation Sequence

    Dripping of cleaner to the lower portions of the building should be minimized. When some rundown is unavoidable, the areas should be rinsed as soon as possible, to eliminate streaking. Generally, the clean and rinse operations move from top to bottom of the building. Avoid drips and splashes during cleaning. Remove dripping as quickly as possible. Note: In case of one storey or low elevation buildings, it is recommended to CLEAN FROM BOTTOM UP and RINSE FROM TOP DOWN.

    Coating Protection

    Always be aware that it is very difficult to remove sealant and machine oils after hardening. During construction, the protective film should be remained as long as possible, to protect the coated surface from stains caused by sealant and machine oils. If adhered, these stains should be removed as early as possible before hardening, with suitable detergents. Remarks A. Do not use strong organic solvents, such as MEK (Methyl Ethyl Ketone), MIBK (Methyl Iso-butyl Ketone), Triclene and paint thinner. B. Do not mix different cleaners. If cleaners needed to be mixed, please follow the manufacturer's instructions. Generally the cleaner containing abrasives cannot be used. Do not mix cleaners. Avoid excessive rubbing, as it may deter the surface gloss. C. Avoid extreme temperature to clean the coated surface. Heat may accelerate chemical reactions and may evaporate the water from solution. Extremely low temperature may give poor cleaning effects. On the contrary, cleaning under higher temperature may result in streaking or straining. Ideally, cleaning should be done on the shaded side of the building under moderate temperature.

    Scratch Prevention

    Make sure that Cleaning sponges or rags are grit free to prevent the coated surface from scratch. Avoid over cleaning or excessive rubbing.

    Residue Cleaning

    In the event adhesive residue is seen on the panels use.

    Protective Film Removal

    It is recommended to remove protective film within 3 months of installation if the protective film remover is exposed for a longer duration, there is a possibility of the film sticking to panels. In this event remove the film carefully in small steps and clean any residue as per above.

    Protective Peel-Off Foil

    Unless otherwise specified, Alubond U.S.A is supplied with a factory applied peel-off foil for protection of the coated surface. Removal of the protective foil is recommended as soon as possible after installation. In hot weather conditions, some residual glue may stick to the stove-lacquered panel's surfaces. Please ask for specific instructions for removal.

    Ozone Friendly

    Neither during the production of Alubond U.S.A nor after being applied as a building cladding are volatile propellant agents of type CFC set free. Alubond U.S.A core material does not contain nitrogen, chlorine or sulphur. By means of its positive contribution to the protection of the environment, the choice of Alubond U.S.A for a huge variety of projects is brilliant.


    Protect pallets during storage against rain, penetration of moisture or condensation. Pile pallets in stacks one on top of the other (do not place the panels in an upright position); Stacks must not comprise of more than 6 pallets of identical size. Avoid storage for a period of more than 6 months.

    Directional Color Appearance

    To avoid possible reflection differences, it is recommended that panels be installed in the same direction i.e. with the orientation of the marking shown on the peel-off-foil of the individual panels running parallel to each other. Also for a single project, use as much sheets as possible from one production batch to avoid even slight variations of color. If different batches at different times are to be used care must be taken to match the color of the previous batch before proceeding with the installation. In case of minor color deviation, it is advisable to use the new panels in a different row and / or away from the previous lot.


    Alubond U.S.A ACP is fully recyclable, i.e. both the core material and the aluminum cover sheets can be re-melted and used for the production of new material.
  • Specifications


    Panels shall be exterior grade, 4mm thick composed of a low density Polyethylene Core sandwiched between two sheets of Aluminum of 0.5mm thickness. The outer top skin shall be coated with either PVDF KYNAR 500(more than 70% PVDF resin) or Fluoropolymer coating. Paint approved suppliers shall be Akzo Nobel, Australia, Monopol Switzerland and P.P.G, U.S.A. There shall be a protective coating on the back skin.

    Product Warranty And Tests:

    Panels shall be installed as per the fixing details and accessories recommended by the Manufacturer and shall carry a 10 years Warranty on weather durability, UV color fading, corrosion, chalking, fading, weather damage and manufacturing defects. Panels shall be extensively tested in compliance to ASTM, BS standards and ISO 9001 requirements. Copies of test Certificates from recognized International Laboratories like Warrington Fire Research Center U.K, Architectural Testing Incorporation U.S.A, VKF Switzerland and SWRI, U.S.A shall be submitted along with the material submittal. Fire rated grade shall carry minimum 60 minutes ASTM E119 fire rating certificate and ASTM D648 deflection temperature rating of 2110C FR core shall be from Dupoint resins containing inorganic mineral core. Alubond U.S.A panels shall be supplied from either one of the Production Plants based in U.S.A, U.A.E, EUROPE & INDIA. All supplied products shall carry authentic Alubond U.S.A Logo and designs, Protective Film of American Building Technologies Inc., U.S.A.


    Deviation Tolerances:

    Thickness: 0.2mm Width: 2.0mm Length: 3.0mm
    Diagonal < 3.0mm (length 2500mm) < 5.0mm (length 2500mm)
    Side straightness: < 0.5% of the length

    Fixing Details and Accessories:

    Typical fixing details and accessories shall be as per the Manufacturer's recommendation and as per the enclosed drawings. All shop drawings will need to be endorsed for submission by the Local Supplier before submittal.


    Panels shall comply with the following performance standards. Specifications

    Color Choice:

    Color shall be as per the selection of the Client / Architect.

    Product Warranty:

    All panels supplied on the project shall be warranted for a period of 10 years by the parent company American Building Technologies Inc, Denver U.S.A as per their standard Product Warranty. Material submittals shall carry a letter from ABTI confirming their willingness to provide the above warranty. The warranty shall be provided directly in the name of The Client from the Manufacturers and endorsed by the local supplier / Installer.
  • Quality

    Alubond U.S.A - Reliable Quality

    We produce Alubond U.S.A and its affiliated materials under the proper control based on ISO 9001:2000 and ISO 14001: 2004 quality assurance system from the coil coating lines to the continuous laminating lines. Our mission to deliver high quality products and services on time at the right price makes our products and services the prime choice for our stakeholders worldwide. We will achieve this through constant innovation and commitment to R & D with a highly committed work force. ISO Quality ISO Quality ALUBOND Europe ISO Quality
  • Download Centre
    Download Centre


    Alubond U.S.A Technical Brouchure (pdf)
    Alubond Stainless Steel (pdf)
    Alubond Green (pdf)
    Alubond Solid (pdf)
    Alubond Lite (pdf)
    Alubond Solar (pdf)
    Alubond PV Booster Mirror (pdf)
    Alubond Acoustics (pdf)

    Color Charts

    Alubond Standard Color Chart (pdf)
    Wood and Stone Color Chart (pdf)
    Sparkle and Prismatic Color Chart (pdf)


    ASTM Standards - U.S.A (pdf)
    Warrington Fire Standards - U.K (pdf)
    Incorporation Certificate - U.S.A (pdf)
    ISO 9001-2000 Certificate (pdf)
    DIN & EN Standards - Germany (pdf)
    Swiss Standards - Switzerland (pdf)
    IIT Bombay - Bombay (pdf)
    ASTM 119 - Fire Test Report (pdf)


    Architectural Approvals (pdf)
    Petrol Station Approvals (pdf)


    Alubond U.S.A Product Warranty (pdf)
    Alubond U.S.A Fixing Details (pdf)
    Alubond U.S.A Specifications (pdf)
    Alubond U.S.A Processing Methods (pdf)
    Alubond U.S.A Method of Statement (pdf)
    Alubond U.S.A Storage & Maintenance (pdf)
    Alubond U.S.A Cleaning Method (pdf)
    Promotional Materials Price List (pdf)
    Alubond U.S.A Structural Design Calculations (pdf)